Showing posts with label dc. Show all posts
Showing posts with label dc. Show all posts

Friday, December 27, 2013

DC 1 3V to 22V Adjustable Regulator

This compact regulator PCB can be used to produce a fully regulated DC supply ranging from 1.3V to 22V at currents up to 1A. Depending on how much current you need, it can fit into tiny spaces and is easily connected with 2-pin headers for DC input, DC output, an on/off switch and a LED. There are many fixed-voltage IC regulators available such as those with 5V, 6V 8V, 9V, 12V & 15V outputs.

DC 1.3V to 22V Adjustable Regulator

But what if you want a voltage output that does not fit into one of the standard ranges or if you want to be able to easily adjust this output voltage? The MiniReg is the answer: it can be set to provide the exact voltage you require. It is based on an LM317T 3-terminal regulator. The PCB has only a few other components: three diodes, three capacitors, two resistors and a trimpot to set the output voltage from the regulator.

DC 1.3V to 22V Power Supply Circuit Diagram
DC 1.3V to 22V Power Supply Circuit Diagram

Diagram shows the circuit details. The LM317T adjustable regulator provides a nominal 1.25V between its OUT and ADJ (adjust) terminals. The output voltage from REG1 is set by the 110O resistor (R1) between the OUT and ADJ terminals and by the resistance between the ADJ terminal and ground. This works as follows: by using a 110O resistor and assuming an exact 1.25V reference, the current flow is set at 11.36mA. This is calculated by dividing the voltage between the OUT and ADJ terminals (1.25V) by the 110O resistor.

This current also flows through trimpot VR1. This means that if VR1 is set to a value of 1kO , then the voltage across this resistor will be 1kO x 11.36mA or 11.36V. This voltage is then added to the 1.25V reference to derive the output voltage ñ in this case 12.61V. In practice, the current flow out of the ADJ terminal also contributes slightly to the final output voltage. This current is of the order of 100µA. So if VR1 is set to 1kO , this can add 0.1V to the output, ie, we get 12.71V.

If you are interested in the output voltage equation, then it is:

VOUT = VREF(1 + R1/R2) + IADJ x R2

where VOUT is the output voltage, VREF is the voltage between the OUT and ADJ terminals and IADJ is the current out of the ADJ terminal (typically 50µA but as high as 100µA). R1 is the resistance between the OUT and ADJ terminals, while R2 is the resistance between the ADJ terminal and ground. Diode D1 in series with the input provides reverse polarity protection. This means that if you connect the supply voltage around the wrong way, you cannot do any damage.

Diode D2 protects the regulator if the input becomes shorted to ground while it is powered up. Without D2, current would attempt to flow back from the output capacitor through the regulator to the shorted input and that could kill it. But D2 becomes forward biased and conducts, effectively preventing any reverse current flow through REG1.

Diode D3 is also included to protect REG1. It does this by clamping the voltage between the ADJ terminal and the OUT & IN terminals in the event that one of the latter is shorted to ground. Finally, capacitors C1 & C2 reduce ripple and noise by bypassing the IN (input) and ADJ terminals respectively. C3 prevents regulator oscillation by swamping any low-value capacitance that may be connected to this output.

See More Detail[...]

Friday, August 9, 2013

All Constructing Various DC Power Supplies Projects



One of the fundamental building blocks of electronics challenge is building your personal DC energy supplies from an AC source of one hundred ten V.A.C or 220 V.A.C.The fashionable DC voltages which are essential to energy up the devices are frequently within the vary of three V DC to 30 V DC. Usually the fixed types of DC voltages are 5V, 9V, 12V, 15V & 18V DC. With the development of know-how, plenty of instruments are the use of one.8 V DC nowadays. S M P S is turning into in style this existing day because the demand for miniaturization due to area constraints will increase.

Take note that for linear energy supply projects, you wish to make use of a step down power transformer to step down the AC voltage from the road voltage of 110 V.A.C or 220 V.A.C ahead of the usage of it to produce to the diode bridge.
See More Detail[...]

Saturday, April 13, 2013

zBot 10 A Power Stage for DC Motor

If\r\n you take a look at the chassis of the zBot vehicle1, you’ll find two sections \r\nrequiring intelligent keep a watch on: the steerage servo and the DC motor. The \r\nso known as H-bridge is the normal circuit for electronic control of \r\nrevolution pace and route. The DC motor of a Tamiya automobile is powerful\r\n sufficient to propel zBot at as so much as 20 miles per hour.
The\r\n motor then consumes more than 10 A, so we make a selection high-current energy \r\nMOSFETs for the cause force stage. There are numerous totally different softwares to \r\nchoose from. The MOSFET we require has to provide the maximum motor \r\ncurrent and, importantly, it needs to be switched with gate voltages of \r\nabout 5 V. In this case, the microcontroller switches the ability stage \r\n(‘low aspect’) directly. For high aspect riding degree shifters are \r\nnecessary. The schematic of the H-bridge power stage presentations a few \r\ninverters, NAND gates and two tri-stateable drivers. These logic \r\nfunctions are essential as the better approach, i.e.., in an instant \r\ncontrolling all 4 MOSFET has a fatal disadvantage.


In\r\n case of a software crash it may well happen that two ore extra MOSFETs are \r\nswitched on incor-rectly for exam-ple, T4 and T7. In that case, the \r\ncurrent throughout the transistors is proscribed by using the interior resistors of \r\nthe MOSFETs (about 10 mO) simplest. Such a deadly error would destroy the \r\nMOSFETs. The common sense performs configured here successfully avoid illegal \r\nstates.To keep an eye fixed on the DC motor, three signals are needed: DIR, PWM and \r\nSTOP. DIR regulates the path of the motor revolution, PWM the rate,\r\n and STOP brakes the motor.

The\r\n software program module for the DC motor is called dcm.c.(070172-I) The \r\ncomplete document referred to as Zbot  the Robot Experimental Platform is \r\navailable free of charge downloading from the Elektor Electronics site. The\r\n file quantity is 070172-11.zip (July/August 2007).
 
 
http://www.ecircuitslab.com
See More Detail[...]