Wiring panel: audio

Showing posts with label audio. Show all posts

Thursday, December 26, 2013

USB Powered Audio Power Amplifier

This circuit of multimedia speakers for PCs has single-chip-based design, low-voltage power supply, compatibility with USB power, easy heat-sinking, low cost, high flexibility and wide temperature tolerance. At the heart of the circuit is IC TDA2822M. This IC is, in fact, mono-lithic type in 8-lead mini DIP package. It is intended for use as a dual audio power amplifier in battery-powered sound players. Specifications of TDA2822M are low quiescent current, low crossover distortion, supply voltage down to 1.8 volts and minimum output power of around 450 mW/channel with 4-ohm loudspeaker at 5V DC supply input.

An ideal power amplifier can be simply defined as a circuit that can deliver audio power into external loads without generating significant signal distortion and without consuming excessive quiescent current. This circuit is powered by 5V DC supply available from the USB port of the PC. When power switch S1 is flipped to ‘on’ position, 5V power supply is extended to the circuit and power-indicator red LED1 lights up instantly. Resistor R1 is a current surge limiter and capacitors C1 and C4 act as buffers. Working of the circuit is simple. Audio signals from the PC audio socket/headphone socket are fed to the amplifier circuit through components R2 and C2 (left channel), and R3 and C3 (right channel)

USB Powered Audio Power Amplifier Circuit diagram:

Potmeter VR1 works as the volume controller for left (L) channel and potmeter VR2 works for right (R) channel. Pin 7 of TDA2822M receives the left-channel sound signals and pin 6 receives the right-channel signals through VR1 and VR2, respectively. Ampl i f ied signals for driving the left and right loudspeakers are available at pins 1 and 3 of IC1, respectively. Components R5 and C8, and R6 and C10 form the traditional zobel network. Assemble the circuit on a medium-size, general-purpose PCB and enclose in a suitable cabinet. It is advisable to use a socket for IC TDA2822M. The external connections should be made using suitably screened wires for better result.

Sucre: http://www.ecircuitslab.com/2011/06/usb-powered-audio-power-amplifier.html

See More Detail[...]

Friday, October 4, 2013

Moduler Audio Preamplifier

High Quality, Discrete Components Design, Input and Tone Control Modules

To complement the 60 Watt MosFet Audio Amplifier a High Quality Preamplifier design was necessary. A discrete components topology, using + and - 24V supply rails was chosen, keeping the transistor count to the minimum, but still allowing low noise, very low distortion and high input overload margin. Obviously, the modules forming this preamplifier can be used in different combinations and drive different power amplifiers, provided the following stages present a reasonably high input impedance (i.e. higher than 10KOhm).

Main Module:

If a Tone Control facility is not needed, the Preamplifier will be formed by the Main Module only. Its input will be connected to some sort of changeover switch, in order to allow several audio reproduction devices to be connected, e.g. CD player, Tuner, Tape Recorder, iPod, MiniDisc etc. The total amount and type of inputs is left to the choice of the home constructor. The output of the Main Module will be connected to a 22K Log. potentiometer (dual gang if a stereo preamp was planned). The central and ground leads of this potentiometer must be connected to the power amplifier input.

Circuit diagram:

Main Module Circuit Diagram

Parts:
R1_____________1K5 1/4W Resistor
R2_____________220K 1/4W Resistor
R3_____________18K 1/4W Resistor
R4_____________330R 1/4W Resistor
R5_____________39K 1/4W Resistor
R6_____________56R 1/4W Resistor
R7,R10_________10K 1/4W Resistors
R8_____________33K 1/4W Resistor
R9_____________150R 1/4W Resistor
R11____________ 6K8 1/4W Resistor
R12,R13________100R 1/4W Resistors
R14____________100K 1/4W Resistor
C1_____________220nF 63V Polyester Capacitor
C2_____________220pF 63V Polystyrene or ceramic Capacitor
C3_____________1nF 63V Polyester or ceramic Capacitor
C4,C7__________47µF 50V Electrolytic Capacitors
C5,C6__________100µF 50V Electrolytic Capacitors
Q1,Q2__________BC550C 45V 100mA Low noise High gain NPN Transistors
Q3_____________BC556 65V 100mA PNP Transistor
Q4_____________BC546 65V 100mA NPN Transistor

Tone Control Module:

This Module employs an unusual topology, still maintaining the basic op-amp circuitry of the Main Module with a few changes in resistor values. A special feature of this circuit is the use of six ways switches instead of the more common potentiometers: in this way, precise "tone flat" setting, or preset dB steps in bass and treble boost or cut can be obtained. Tone Control switches also allow a more precise channel matching when a stereo configuration is used, avoiding the frequent poor alignment accuracy presented by common ganged potentiometers. Six ways (two poles for stereo) rotary switches were chosen for this purpose as easily available. This dictated the unusual "asymmetrical" configuration of three positions for boost, one for flat and two for cut.

This choice was based on the fact that tone controls are used in practice more for frequency boosting than for cutting purposes. In any case, +5dB +10dB and +15dB of bass boost and -3dB and -10dB of bass cut were provided. Treble boost was also set to +5dB +10dB and +15dB and treble cut to -3.5dB and -9dB. Those wishing to use common potentiometers in the usual way for Tone Controls may use the circuit shown enclosed in the dashed box (bottom-right of the Tone Control Module circuit diagram) to replace switched controls. The Tone Control Module should usually be placed after the Main Input Module, and the volume control inserted between the Tone Control Module output and the power amplifier input. Alternatively, the volume control can also be placed between Main Input Module and Tone Control Module, at will. Furthermore, the position of these two modules can be also interchanged.

Circuit diagram:

Tone Control Module Circuit Diagram

Parts:

R1,R7___________47K 1/4W Resistors
R2_____________220K 1/4W Resistor
R3______________18K 1/4W Resistor
R4_____________330R 1/4W Resistor
R5______________39K 1/4W Resistor
R6______________56R 1/4W Resistor
R8_____________150R 1/4W Resistor
R9______________10K 1/4W Resistor
R10,R16__________6K8 1/4W Resistors
R11,R12________100R 1/4W Resistors
R13____________100K 1/4W Resistor
R14______________1K5 1/4W Resistor
R15,R21,R22______4K7 1/4W Resistors
R17,R24,R26______8K2 1/4W Resistors
R18______________3K3 1/4W Resistor
R19______________1K 1/4W Resistor
R20____________470R 1/4W Resistor
R23,R25_________12K 1/4W Resistors
R27,R28__________4K7 1/4W Resistors
C1_____________220nF 63V Polyester Capacitor
C2_______________1nF 63V Polyester or ceramic Capacitor
C3,C6___________47µF 50V Electrolytic Capacitors
C4,C5__________100µF 50V Electrolytic Capacitors
C7______________10nF 63V Polyester Capacitor
C8,C9__________100nF 63V Polyester Capacitors
Q1,Q2_________BC550C 45V 100mA Low noise High gain NPN Transistors
Q3____________BC556 65V 100mA PNP Transistor
Q4____________BC546 65V 100mA NPN Transistor
SW1,SW2_______2 poles 6 ways Rotary Switches
Simpler, alternative Tone Control parts:
P1______________22K Linear Potentiometer
P2______________47K Linear Potentiometer
R29,R30________470R 1/4W Resistors
R31,R32__________4K7 1/4W Resistors
C10_____________10nF 63V Polyester Capacitor
C11,C12________100nF 63V Polyester Capacitors

Power supply:

The preamplifier must be feed by a dual-rail, +24 and -24V 50mA dc power supply. This is easily achieved by using a 48V 3VA center-tapped mains transformer, a 100V 1A bridge rectifier and a couple of 2200µF 50V smoothing capacitors. To these components two 24V IC regulators must be added: a 7824 (or 78L24) for the positive rail and a 7924 (or 79L24) for the negative one. The diagram of such a power supply is the same of that used in the Headphone Amplifier, but the voltages of the secondary winding of the transformer, smoothing capacitors and IC regulators must be uprated. Alternatively, the dc voltage can be directly derived from the dc supply rails of the power amplifier, provided that both 24V regulators are added.

Note:

If this preamplifier is used as a separate, stand-alone device, thus requiring a cable connection to the power amplifier, some kind of output short-circuit protection is needed, due to possible shorts caused by incorrect plugging. The simplest solution is to wire a 3K3 1/4W resistor in series to the output capacitor of the last module (i.e. the module having its output connected to the preamp main output socket).

Technical data:

Main Module Input sensitivity:: 250mV RMS for 1V RMS output
Tone Control Module Input sensitivity:: 1V RMS for 1V RMS output
Maximum output voltage:: 13.4V RMS into 100K load, 11.3V RMS into 22K load, 8.8V RMS into 10K load
Frequency response:: flat from 20Hz to 20KHz
Total harmonic distortion @ 1KHz:: 1V RMS 0.002% 5V RMS 0.003% 7V RMS 0.003%
Total harmonic distortion @10KHz:: 1V RMS 0.003% 5V RMS 0.008% 7V RMS 0.01%

Source : www.redcircuits.com

See More Detail[...]

Tuesday, July 30, 2013

Dual 20 Watt Audio Power Amplifier

Overture Audio Power Amplifier Series Dual 20-Watt Audio Power Amplifier with Mute and Standby Modes

The LM1876 is a stereo audio amplifier capable of delivering typically 20W per channel of continuous average output power into a 4

or 8

load with less than 0.1% THD+N. Each amplifier has an independent smooth transition fade-in/out mute and a power conserving standby mode which can be controlled by external logic.

The performance of the LM1876, utilizing its Self Peak Instantaneous Temperature (°Ke) (SPiKe™) protection circuitry, places it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area (SOA). SPiKe protection means that these parts are safeguarded at the output against overvoltage, undervoltage, overloads, including thermal runaway and instantaneous temperature peaks.

Dual 20-Watt Audio Power Amplifier Circuit diagram :

Key Specification

THD+N at 1kHz at 2 x 15W continuous average
output power into 4 or 8:	0.1% (max)
THD+N at 1kHz at continuous average
output power of 2 x 20W into 8:	0.009% (typ)
Standby current:	4.2mA (typ)

Applications :

High-end stereo TVs

Component stereo

Compact stereo
Features :

SPiKe protection

Minimal amount of external components necessary

Quiet fade-in/out mute mode

Standby-mode

Isolated 15-lead TO-220 package

Non-Isolated 15-lead TO-220 package

Wide supply range 20V - 64V

Source : http://www.ecircuitslab.com/2011/06/dual-20-watt-audio-power-amplifier.html

See More Detail[...]

Wednesday, June 12, 2013

TDA1562Q 36 Watt Audio Power Amplifier circuit and explanation

36 Watt Audio Power Amplifier Circuit Using TDA1562Q

Its based on a Philips class-H audio amplifier IC and can deliver 36W RMS OR 70W music power, all from a 13.8V supply. Our new Mighty Midget Amplifier can really pack a punch - around 36W RMS continuous into a 4-ohm load when using a 13.8V supply. However, its the 70W of output power that it can deliver during dynamic (music) signal conditions that really make you sit up and take notice.

Picture of 36 Watt Audio Power Amplifier Using TDA1562Q

As can be seen from the photos and the circuit diagram, the Mighty Midget uses just a handful of parts. Its built on a PC board that measures just 104mm x 39mm but while its size may be modest, theses nothing at all modest about its power output. And the noise and distortion figures are pretty good too.

Circuit diagram:

36 Watt Audio Power Amplifier Circuit Diagram

At the heart of the circuit is the TDA1562Q IC, described by Philips as a "monolithic integrated Bridge-Tied Load (BTL) class-H high-efficiency power amplifier". It comes in a 17-pin "DIL-bent-SIL" plastic package and is not only designed for use in car audio and portable PA work but for mains applications as well; eg, mini/midi audio components and TV sound.

Parts layout:

Parts Layout Of 36 Watt Audio Power Amplifier

PCB layout:

Performance:

Output power:----------------------36W RMS into 4R
Music power:-----------------------70W into 4R
Frequency response:---------------1dB down at 28Hz and 55kHz
Input sensitivity:-------------------130mV RMS (for 36W into 4?)
Harmonic distortion:----------------typically 0.2% (see graphs)
Signal-to-noise ratio:----------------95dB unweighted (22Hz to 22kHz)

Source: Silicon Chip March 2002

See More Detail[...]

Saturday, April 13, 2013

Simple 500W Audio Power Amplifier Circuit Diagram with Transistor

We take transistor MJL2194 and MJL2193 for pressure output signal.so the amp has a capability for enormous instantaneous current potential.

Circuit Functional
I use the -85 volt when the output current is supplied to the drive 350 to 340 very hot. Increase the output present, but it was once too chilly. The output to warmth up sooner than a regular open it. Sounds evident, but sound high quality is somewhat excellent.

I recomment it by way of turning out for the evening. If the force is installed on the steel part out.

I assume simple. View full above, the statement that R 30 ohm then the voltage throughout the 0.86 V exhibit that the brand new via its 29 mA for those who add a file to / – eighty five V, and think that the voltage throughout the part physique. It was the identical in each the R 30 ohm to get an awfully light 5 zero.86 = 5.86 V and the present I can be 5.86/30 = zero.195 A = 195 mA, and the specification of mje340. mje350 get Ic (max) = 500 mA, so it is pure for it to heat up. Actually, it isn't essential to adhere to sync tr output must be interested in the following two tr power force is healthier. For VR will have to be R300 .

See More Detail[...]

Sunday, April 7, 2013

A Low Distortion Audio Pre amplifier

In an audio amplifier the quality of sound depends upon a number of factors, e.g. quality of active and passive components, circuit configuration, and layout. To an extent, the selection of components depends on the constructor’s budget. The discrete active components like transistors have been increasingly replaced by linear ICs, making the task of designer easier. With the passage of time, the general-purpose op-amps like LM741, which were being used in audio/hi-fi circuits, have become The preamplifier circuit presented here is based on a dual precision op-amp for the construction of a low distortion, high quality audio preamplifier.

Low Distortion Audio Pre-amplifier Circuit diagram:

A dual op-amp OPA2604 from Burr-Brown is used for all the stages. The FET input stage op-amp was chosen in this context it is worthwile to mention another popular bi-polar architecture op-amp, the NE5534A. It has, no doubt, an exceptionally low noise figure of 4nV/ÖHz but rest of the specifications compared to OPA2604 are virtually absent in this IC. Also This IC is also capable of operating at higher voltage rails of ± 24V (max.). Also its input bias current (100 pA) is many orders lower than its bipolar counterpart’s. This ensures a multifold reduction in noise.

A channel seperation of 142 dB exists between In the circuit, buffer is essential for the proper working of the subsequent blocks. A nominal input impedance of 47k is offered by this stage which prevents overloading of the preamplifier. The tone control is a baxandall type filter circuit.The bandwidth limiter is basically a low-pass filter with an upper cut-off ceiling at the end of the useful audio spectrum. The gain at 10 kHz is approximately 17 dB. The design is essentially 3-pole type and the upper frequency is set at 25 kHz. This lSetting the unit is fairly simple. Check the power leads feeding the IC for symmetrical voltages. High quality audio output from the line output socket is to be fed as the input signal to this preamplifier. Output of the preamplifier is fed to the power a The whole circuit consumes about 10 mA when the above-mentioned ICs are used. Power supply requirements are not critical as the circuit works on 7.5V to 15V DC..

Source : http://www.ecircuitslab.com/2012/01/low-distortion-audio-pre-amplifier.html

See More Detail[...]